不锈钢门套线包边的做法

The method of stainless steel door frame wire edge wrapping

一.用冲击电钻在门4周大洞眼,并插入木楔。

1、 Use an impact drill to drill a large hole around the door and insert a wooden wedge.

二.将一五厘大芯板(或者夹板)靠墙侧进行防潮处理(刷光油二遍后在贴珍珠棉)。用钉校订固定后,再用铁钉加固。门套线条打底用九厘夹板。打底夹板外侧用实木线条收口。合页位置加板衬固或者封两层一五厘大芯板。

2、 Apply moisture-proof treatment to the side of the 15mm large core board (or plywood) against the wall (apply two coats of varnish before applying pearl cotton). After fixing with nails, reinforce with iron nails. Use a 9mm plywood to base the door frame lines. Close the outer side of the bottom plywood with solid wood lines. Add a board lining or seal two layers of a 15mm large core board at the hinge position.

三.门套与门扇相合的地方到进门边的侧面用九厘夹板做止口板,止口深度与门的厚度相同。

3、 Use a 9mm plywood as a stop plate from the point where the door frame meets the door leaf to the side of the entrance door, with the depth of the stop plate being the same as the thickness of the door.

四.面板用白乳胶涂匀后贴于打第大芯板及止口板上,并用不锈钢蚊钉适量加固。

4、 Apply white latex evenly to the panel, then stick it onto the second core board and stop plate, and reinforce it with stainless steel mosquito nails in an appropriate amount.

五.门套线条宽度1般为六0—八0.厚度八.

5、 The width of the door frame line is generally 60-80. The thickness is 8

六.厨卫门套线条里侧用不锈钢(哑光)线条为好。

6、 It is better to use stainless steel (matte) lines on the inner side of the kitchen and bathroom door frames.

七.门套及门窗套垂直、水平误差不超过二(二m以上不超过三)对于角线误差不超过三(二m以上不超过五).

7、 The vertical and horizontal errors of door and window frames shall not exceed two (no more than three for a distance of two meters), and the errors of corner lines shall not exceed three (no more than five for a distance of two meters)

八.门套双侧墙与门套之间距离在门套线条不能压住接缝时,宜先用水泥沙浆挂钢钉封平(用板定模灌浆)干燥后方可封板打第,在门套线条能压住接缝时可用板封龙骨结构。

8、 When the distance between the walls on both sides of the door frame and the door frame cannot press the joint with the door frame line, it is advisable to first use cement mortar to hang steel nails for sealing (using plate fixed mold grouting) and dry before sealing the board. When the door frame line can press the joint, the board can be used to seal the keel structure.

九.单面门套用九厘板打底(凸窗应注意窗帘位置)。其他与双面门套同。入户大门可封单边实木线条门套。

9、 Single sided door frames should be bottomed with a 9mm board (attention should be paid to the position of curtains for protruding windows). Other items are the same as double-sided door frames. The entrance door can be sealed with single-sided solid wood line door frames.

一0.窗套不宜包台面,台面用大理石铺贴(防盗网宜在窗套面板封后制作)。单面门套:在原来有门的基础上起装潢作用,不起经受门的气力。

10. The window cover should not cover the countertop, and the countertop should be paved with marble (the anti-theft net should be made after the window cover panel is sealed). Single sided door frame: It serves as a decoration on the basis of the original door and does not withstand the force of the door.

做不锈钢门套线包边的注意事项

Notes on making stainless steel door frame wire edging

不锈钢门套线包边1般都是定制,很少有现场制作的,由于目前工人的技术水平达不检修评定标准,而且现场也没有专业的不锈钢施工作人员。

Stainless steel door frame wire edging is usually customized and rarely produced on site. Due to the current technical level of workers not meeting the inspection and evaluation standards, and the lack of professional stainless steel construction personnel on site.

在制作不锈钢门套的时候,咱们都是按门套基层的尺寸画好图,该折的部位厂家折好,采取全能胶或者者玻璃胶粘贴,立面与顶面交接也不用焊接!

When making stainless steel door frames, we always draw according to the size of the base layer of the door frame. The manufacturer folds the parts that need to be folded and uses universal glue or glass glue to stick them. There is no need to weld the connection between the facade and the top surface!

本文由德州电梯不锈钢包边友情奉献.更多有关的知识请点击: http://m.nthly.cn真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by Texas Elevator's stainless steel edging friendship. For more information, please click: http://m.nthly.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned