Check the specification, opening direction and relevant accessories of the door according to the design drawings.

用卷尺量门洞的高与宽。门的标准高宽尺寸是200cm×80cm；卫生间的门高宽是200cm×70cm。尺寸如有出入要及时纠正。

Measure the height and width of the door opening with a tape measure. The standard height and width of the door is 200cm × 80cm； The height and width of the toilet door is 200cm × 70cm。 Any discrepancy in size shall be corrected in time.

测量位置线，确定门框的位置，用墨斗弹拉出垂直线，一侧门洞两条垂直线。

Measure the position line, determine the position of the door frame, pull out the vertical line with an ink fountain, and two vertical lines of the door opening on one side.

在垂直线上用冲击钻打眼，孔眼与孔眼之间的距离约为30cm，一侧门两排共10个孔眼。冲击钻的钻头应为12mm，所钻孔眼深度约为6cm。

Drill holes on the vertical line with an impact drill. The distance between the holes is about 30cm. There are 10 holes in two rows of one side door. The bit of percussion drill shall be 12mm, and the drilling depth shall be about 6cm.

将小木楔用铁锤逐个钉入孔眼，以便固定门框板。小木楔的体积大小为5cm×1.5cm×1.5cm，以落叶松制作的为好，因为落叶松的木质结构紧，不容易松动。

Hammer the small wooden wedges into the holes one by one to fix the door frame plate. The volume of the small wooden wedge is 5cm × 1.5cm × 1.5cm, preferably made of larch, because the wood structure of larch is tight and not easy to loosen.

开料制作门框。左右做两侧门框龙骨的木工板尺寸为200cm× 3cm×8cm，门框顶龙骨的木工板尺寸为80cm×3cm×8cm。将高密度九厘板涂胶粘在龙骨上，再用钉固定。

Cut materials to make door frame. The dimension of the woodworking board for the keel of the door frame on the left and right sides is 200cm ×  3cm × 8cm, the dimension of the woodworking board of the keel on the top of the door frame is 80cm × 3cm × 8cm。 Glue the high-density 9cm board to the keel and fix it with nails.

将制作好的三条门框按门的形状连接起来，并且用大钉子在接合处固定。

Connect the three fabricated door frames according to the shape of the door, and fix them at the joint with large nails.

用刨子将连接好的门框表面修平整，修整边角，棱角分明。

Use a plane to smooth the surface of the connected door frame and trim the edges and corners with clear edges and corners.

将门框放到门洞上，按墙面的水平线为准，门框下拿木头或者砖头垫起，调节门框的高度。下面预留5cm埋在地板的龙骨中。

Put the door frame on the door opening, subject to the horizontal line of the wall, take wood or brick under the door frame and adjust the height of the door frame. Reserve 5cm below and bury it in the keel of the floor.

在门框的上面钉一个钉子，把线垂挂上，通过线垂来调整门框的垂直，一边衡量一边用麻花钉将门框固定在门洞上。

Nail a nail on the doorframe, hang the thread vertically, adjust the vertical of the door frame by line, and measure the door frame with a twist pin on the doorway.

制作门脸的线条。门脸可以是现成买的，也可以是施工人员按照图纸做出来的。制作完成后，就把门脸固定到门框上六，这样门套就基本完成了。

Make the lines of the door face. The door face can be bought off the shelf or made by the construction personnel according to the drawings. After making, fix the door face to the door frame, so that the door pocket is basically completed.

把门放到门套上比划好，确定合页在门套上的具体位置，再按合页的厚度切出口径。也切出锁套的口径。将门安装到门套上，合页用锣丝刀将锣丝钉拧紧。注意门与门套的间隙不得大于1.5mm，以顺畅开关门为准。

Put the door on the door pocket, make a comparison, determine the specific position of the hinge on the door pocket, and then cut the caliber according to the thickness of the hinge. Also cut out the diameter of the lock sleeve. Install the door on the door pocket, and tighten the gongs and screws with a gongs and wire knife on the hinge. Note that the gap between the door and the door pocket shall not be greater than 1.5mm, subject to the smooth opening and closing of the door.

电梯门套线专注行业发展十几年，真诚服务顾客,专注客户需求,您有不明确的内容可点击网站进行详细了解：http://m.nthly.cn

Elevator door pocket line has focused on the development of the industry for more than ten years, sincerely serving customers and focusing on customer needs. If you have unclear content, you can click the website to learn more: http://m.nthly.cn