一、电梯门套安装方法：

1、 Installation method for elevator door frames:

1.将厅门处门洞进行处理。厅门处一般是安装石材覆盖在表面。石材在安装前要进行表面处理，保持清洁和干燥度，含水率要小于8%。

1. Handle the door opening at the hall door. The hall door is usually covered with stone on the surface. Stone should undergo surface treatment before installation to maintain cleanliness and dryness, with a moisture content of less than 8%.

2.用来安装门套的石材应该保持花纹、颜色的一致性。所以要进行仔细甄选，避免出现严重的色差和花纹差异性。每一层的所有电梯门套石材都要保持统一性。

2. The stone used for installing door frames should maintain consistency in pattern and color. So careful selection is necessary to avoid serious color and pattern differences. All elevator door frames on each floor must have consistent stone materials.

3.正式安装石材之间，再将石材做一次彻底清理，结构部分不能留有渣质，表面无积灰污垢。然后用墨线弹出水平线和垂直线。

3. Before formally installing the stone, thoroughly clean the stone again. The structural parts should not have any residue, and the surface should be free of accumulated dust and dirt. Then use ink lines to pop out horizontal and vertical lines.

4.根据弹出的线条位置，使用钻机在需要打孔处打孔。孔眼的直径一般是8mm左右，深度是12mm左右。按照施工标准，每块石板上、下面都要打孔眼，位于石板中间位置。

4. According to the position of the pop-up line, use a drilling rig to drill holes at the required locations. The diameter of the hole is generally around 8mm and the depth is around 12mm. According to construction standards, holes should be drilled above and below each stone slab, located in the middle of the slab.

5.将膨胀螺栓固定在墙面上，然后将角架固定好，再将挂件安装在角架上。

5. Fix the expansion bolt on the wall, then fix the corner bracket, and then install the hanging piece on the corner bracket.

6.角架和挂件安装好之后，进行石材开槽工序。将石材固定在挂件上时使用专用的大理石胶，黏结好之后反复压几次，确定不会脱落。

After the installation of the corner bracket and hanging parts, proceed with the stone slotting process. When fixing the stone on the pendant, use a special marble adhesive. After bonding, press it repeatedly several times to ensure that it does not fall off.

7.安装好之后的电梯门套应该做到光面平整，立面垂直，接缝平直，接缝宽度的偏差不能超过2mm。

7. After installation, the elevator door frame should be smooth and flat, with a vertical facade and straight seams. The deviation in seam width should not exceed 2mm.

8.电梯门套全部安装完之后，将表面石材做一次清理工作，即可投入使用。

After all the elevator door frames are installed, clean the surface stone once and it can be put into use.

二、电梯门套安装知识：

2、 Knowledge of elevator door frame installation:

1、墙面所用石材的种类、大小、性能和等级，应该符合国家的规定等级。

1. The type, size, performance, and grade of stone used on the wall should comply with the national regulations.

2、墙面对大理石的色泽、立面分格、花色、花纹和图案应符合要求。

2. The color, facade division, pattern, pattern, and pattern of marble on the wall should meet the requirements.

3、石材孔、槽的数量、深度、位置、尺寸应符合设计要求不准有裂纹、缺边崩角等现象。

3. The number, depth, position, and size of stone holes and grooves should meet the design requirements and there should be no cracks, missing edges, or corners.

4、墙面干挂部件工艺应符合国家规定。

4. The process of wall hanging components should comply with national regulations.

5、石材表面和板缝的处理应符合设计要求。

5. The treatment of stone surface and slab joints should meet the design requirements.

6、石材表面（六面）均需做防碱化和防水处理。

6. The surface of the stone (six sides) needs to be treated with anti alkalization and waterproofing.

本文由潍坊电梯门套为您提供，我们的网站是：http://m.nthly.cn我们将以全心全意的热情为您提供服务，欢迎您的访问！

This article is provided by Weifang Elevator Door Jamb. Our website is: http://m.nthly.cn We will provide you with wholehearted enthusiasm and welcome your visit!